Home > Failed To > Vmware Error Lock Was Not Free

Vmware Error Lock Was Not Free

Contents

To kill the virtual machine, run this command:# vm-support -X Where theis the World ID of the virtual machine with the locked file.Note: This command takes 5-10 minutes to complete. The files cannot be accessed by the servers while locked, and the virtual machine is unable to power on.These virtual machine files are commonly locked for runtime: .vswp -flat.vmdk --delta.vmdk .vmx Open a remote console window for the virtual machine. Conclusion: My 4 ESX hosts (ESX1, ESX2, ESX3, ESX4)  are in one cluster (Automation). http://ndsman.net/failed-to/vmware-player-failed-to-lock-the-file.php

If it is a third-party process, however, contact the appropriate vendor in order to determine the root-causeprior to killing the process ID, as it may occur again in the future.Stop the Log in to server via ssh, navigate to datastore and folder with virtual machine files, type - touch out put should be: device or resource busy next step is to identify Powering off the other virtual machine using the disk file releases the lock. Theme by Alx. Source

Unable To Power On Vm File Is Locked

It is also case-sensitive. After logging into the server, the process maintaining the lock can be analyzed.Note: If this process does not reveal the MAC address, or the owner identifier is all zeroes, it is View my complete profile Subscribe To Posts Atom Posts Comments Atom Comments My Blog List Yellow Bricks Storage capacity for swap files and TPS disabled 8 minutes ago NTPRO.NL Video - In other circumstances, the file is locked by a VMkernel child or cartel world and the offending host running the process/world must be rebooted to clear it.

Once you find the MAC address as all Zeros, you may try to restart the management agents which will release the lock.To determine if the MAC address corresponds to the host Mikkelsen Remove ignored SSL certificates from VMware VIClient 2 years ago blog.scottlowe.org Nutanix, VMware, Azure, vCloud, vSphere, Hyper-V, Windows Azure Pack About me VMware vSphere Best Practices Nutanix Cool Tools You may press G, once open, to immediately scroll to the bottom of the log's output. An Error Was Received From The Esx Host While Powering On Vm Failed To Create Swap File To address this issue, see Troubleshooting a virtual machine that has stopped responding (1007819).

Cannot power onthe virtual machine after deploying it from a template. Failed To Initialize Swap File Lock Was Not Free If the virtual machine is unable to power on, an error on the remote console screen displays with the name of the affected file. For more information, see Collecting diagnostic information for VMware Products (1008524). hop over to this website To identify the server: Report the MAC address of the lock holder by running the command: vmkfstools -D /vmfs/volumes/// For servers prior to VMware ESX/ESXi 4.1, this command writes the output

Record this information as it is required in the remainder of this process on the ESXi server.Assess the virtual machines current state on the host:For ESX, run this command:# vmware-cmd Failed To Create Swap File '/vmfs/volumes/vsan If it is not listed, the virtual machine is not registered on this ESX/ESXi host. During the power on process, an error may display or be written to the virtual machine's logs. You may pressG, once open, to immediately scroll to the bottom of the log's output.

Failed To Initialize Swap File Lock Was Not Free

have any VMs running on the datastore from any host before removing the lock.As always, if this helped you please leave a comment 🙂Incoming search terms:Lock was not freeCall HostStorageSystem MountVmfsVolume try this Copyright ©2016 Andy Barnes - Please do not copy any content including images without prior consent! Unable To Power On Vm File Is Locked The issue at hand was out of 10 datastores on the SAN one datastore could suddenly no longer be mounted.It showed up as (inactive)(unmounted): Obviously the logical solution would be to Vmware Failed To Create Swap File Not Found AnswerNoto "Can I include a screenshot of the VM", and answerYesto all subsequent questions.After stopping the process, you can power on the virtual machine or access the file/resourceFor ESXi 5. 0,

To address this issue, seeTroubleshooting a virtual machine that has stopped responding (1007819).If the output from this command isgetstate() = off, the ESX host may be unaware of the file lock.For this content If you just tried to power on the VM, then relevant info should be at the end of the log file. You have identified the server via the vmkfstools -D command in earlier steps, the lsof utility yields no offending processes, and no other virtual machines are locking the file. The locking mechanism for VMFS volumes is handled within VMFS metadata on the volume. Vmware Failed To Lock The File Vmdk

Tuesday, April 17, 2012 Could not power on VM - lock was not free The other day we experienced an incident on the SAN storage with high latency and even loss When the host has rebooted, start the affected virtual machine again. If that ESX host has the lock for the virtual machine, it should allow you to power it on.Rebooting the ESX host which is locking the filesBy this stage, you have weblink If another error message is reported, it may indicate that the metadata pertaining to file or directory locking on VMFS may not be valid or corrupt.

Locate the affected virtual machine, and attempt to power it on. File Is Being Locked By A Consumer On Host With Exclusive Lock On the ESXi console, enter Tech Support mode and log in as root. Check using Edit Settings on your backup solution's virtual machine to see if it has a hard disk attached that belongs to a different virtual machine.

Artur holds VMware Certified Design Expert certification (VCDX #077).

As such, the command can be used to test the file and directory locking mechanism in the VMFS filesystem, where the procedure is expected to fail on locked files. For more information, seeCollecting diagnostic information for VMware products (1008524).File a support request with VMware Support and note this KB Article ID in the problem description. Note: If this process does not reveal the MAC address, or the owner identifier is all zeroes, it is possible that it is a Service Console-based lock, an NFS lock (for Failed To Create Swap File Host Doesn't Have A Journal From ESX/ESXi 4.1, the output is also displayed on-screen.

Note: For related information, see Cannot power on a virtual machine because the virtual disk cannot be opened (1004232).Additional Information Posted by santhoshpani at 10:01 AM Email ThisBlogThis!Share to TwitterShare to For more information, see How to Submit a Support Request. To move to the virtual machine's directory, run the command: cd /vmfs/volumes// Use a text viewer to read the contents of the vmware.log file. check over here To confirm that the virtual machine is registered on the server and obtain the full path to the virtual machine, run the command: vmware-cmd -l The output returns a list of

You can identify this by files denoted with .lck.#### (where #### refers to the World ID that has the file lock) at the end of the filename. This may be on any of the ESX hosts which have access to the file. Artur Krzywdzinski says: Hey John, no chance - NGT are supported on Win2008 R2... In a VMFS volume sometimes these files stay locked even when they are not in use (possibly when a VM was not stopped properly).

Using touch is the preferred method because the changes to the resource are minimal.To test the file or directory locking functionality, run this command:# touch Note: Performing a "

The owner locking the file is on the line where it says owner "owner 2a3b5a3-cb2591a3e-b657-e18b9e6d24b6". When the virtual machines have been evacuated, place the host into maintenance mode and reboot it. Related posts: Virtual machine stop logging to vmware.log Error 111 or 503 Service Unavailable - after ESX restart First steps with VMware ESX and ESXi commands usage exupdate and dependency problem To identify the server:Report the MAC address of the lock holder by running the command (except on NFS volume):# vmkfstools -D /vmfs/volumes///Note: Run this command on all commonly locked

Excerpts and links may be used, provided that full and clear credit is given to Artur Krzywdzinski and www.vmwaremine.com with appropriate and specific direction to the original content. For more information, seeCollecting diagnostic information for VMware products (1008524)andHow to Submit a Support Request.Locating the lock and removing itBecause a virtual machine can be moved between hosts, the host where The locking mechanism for VMFS volumes is handled within VMFS metadata on the volume.Determining if the file is being used by a running virtual machineIf the file is being accessed by Incapsula incident ID: 277000480273506460-988315087709471497 Skip to content vabsnanoti Just another WordPress.com site VMware Error : ”Lock was notfree” Sometimes you may receive below error in the Vcenter  for any VM.( In

File a support request with VMware Support and note this KB Article ID in the problem description. You have identified the server via thevmkfstools -Dcommand in earlier steps, thelsofutility yields no offending processes, and no other virtual machines are locking the file.The server should be restarted to allow Note: If you have only one ESX server or do not have the ability to vMotion or migrate virtual machines, you must schedule downtime for the affected virtual machines prior to What to do it that case ?

He has been using, designing and deploying VMware based solutions since 2005 and Microsoft since 2012.